How to install a board and batten wall for super cheap! from Thrifty Decor Chick

How to install a board and batten wall for super cheap! from Thrifty Decor Chick


Soon after likely again and forth on what I preferred for at minimum a year, I just went for it. I hit a snag together the way and redirected…I’ll share that in a moment! 

I started with the least expensive wall since it was the least complicated to achieve. ) This is how it is appeared for awhile right after I developed and mounted my image ledges/cabinets: 
DIY wood picture ledges

I started off by eliminating the trim less than the stairs — it is rather conventional for builders to use baseboard (didn’t get a ahead of pic so this is yet another place on the stairs): 

baseboard as stair trim

The trim I was scheduling to use is 1/4 inch thick and if you butt it up against the more compact aspect of the base, it did not satisfy up to my liking. I needed them to be as flush as attainable. 

This write-up may perhaps contain affiliate links for your convenience. 

I do not Like the baseboards utilised as trim anyway, so I wanted to alter it up. I wanted some thing a small cleaner, so I was planning to use these slim lattice strips from the components retail store: 
Lattice strips for board and batten wall

Here’s the factor that often bites me in the butt. When and awhile I am impatient and just want to get immediately after a task. Commonly I’d have the luan I normally use reduce down rather of acquiring the lattice. Luan is only $15 for a 4×8 piece and it gives you ten or so strips (is dependent on how large you have them lower). 

Point is, I was being lazy and did not want to go seize the wood and have it cut down at the shop. And the cuts usually are not normally Wonderful — it can be a free (or really very low cost) provider and I am so grateful they do that at our nearby components merchants. But sometimes they usually are not slash effectively and you’re still left with a good deal you are not able to use. It just is dependent on who cuts it! I wished to go the easy route this time and I ought to master by now that that won’t usually conclusion nicely. ) 

Soooo…when I took the base off under the stairs, the gap in between the stained wooden and the drywall was way too substantial for me to use the lattice. For all the areas farming the wall, I was likely to have to use a little something broader. 

I didn’t even know I experienced scrap strips of luan by now slice down in our garage from an additional venture. Rating!! I was in a position to get all of the foundation off (besides at the base) and change it with luan:

Installing a board and batten trim wall

This aspect was rather easy due to the fact I just held the old foundation up to the new trim and marked the size and angle it needed to be cut. 

Now my trim experienced a little something it would healthy flawlessly flush from. You can see I also extra some along the remaining facet so the entire point was trimmed out. 

I assumed it’s possible I could still use the thin lattice for the relaxation of the wall so I commenced setting up: 

Board and batten how-to

And I hated it. It appeared all improper. 

I do have to say — until it is really painted it’s really difficult to imagine how it will appear. Maintain that in brain as you do the job on assignments like this. A coat of white paint (or whatsoever shade) will unify every thing and make it search far better 100 per cent of the time. 

I could just inform immediately that the slender strips ended up off with the thicker things framing it.

So I dug all over additional in the garage and observed adequate of the luan strips to complete the whole wall. DUH. I could have saved so significantly time! 

Here is a small trick when you are setting up trim up against an angled wall or trim — maintain the close of the piece you are putting in up against the angle (use a stage to make guaranteed it is really completely horizontal or vertical):

How to get a perfect angle when installing trim

Mark the leading and bottom (and then attract a line if your saw won’t have a laser line). Location your trim on the saw and transfer the noticed angle until it matches up. It will get you an precise match!

Figuring out the spacing for board and batten is a math sport. I figure the area in between the two conclude items of trim on each and every facet of the wall. That was 129 inches. My strips are 4.5 inches wide, so I figured out how numerous I required (four) and subtracted that whole: 

129 inches – 18 (4.5×4) = 111 

Then I divided 111 by how several “open up” areas I’d have vertically. 4 parts of trim means 5 areas so…

111 inches ÷ 5 = 22.2

I finished up performing 22 inches to give myself a minimal wiggle place. 

I additional a horizontal piece throughout the prime (placement is anywhere seems to be greatest) and I was carried out!:

How to install inexpensive board and batten trim

Nicely not carried out completed. Following up: filling holes, light sanding and then at minimum two coats of paint, most likely a few.

I went with a person line throughout horizontally rather of a several since I failed to want it to get way too hectic. It can be easy to get away or increase additional if I want to modify it up. I want this to be an accent that provides character to the home, but I never essentially want it to be the primary focal level. 

I ought to have recognized that I would like the thicker trim much better in any case! That lattice was heading to be way also wimpy. 

I know it’s challenging to imagine this in it’s unfinished condition, but bare with me. When it is all white it will appear advanced, but would not overpower the room. It will be extremely quite when I’m performed…which is the program. ) 

Oh, and I hardly ever approach to eliminate individuals picture ledges so I trimmed all-around them. 

It’s been awhile since I’ve revealed you how to do basic wall trim with this cheap things. You can do so substantially with just a single 4×8 sheet! Continue to be tuned to see that 1st wall finished up.

See under to see just a couple of the tasks I have carried out with these luan boards. It’s uncomplicated to use and appears to be like fantastic when painted! 

Simple and cheap board and batten wall
Extend sides of islands ship lap
Gray shiplap walls with luan

See extra of our home listed here. To shop goods in our property, click listed here! Never miss out on a post by signing up to get posts by way of e-mail. 



Source hyperlink