DIY table leg candlesticks from Thrifty Decor Chick

DIY table leg candlesticks from Thrifty Decor Chick


Hey there! I have a fun desk leg-turned-candlestick Do it yourself for you right now! I’ve
found this concept performed all about, but
my friend Kate
a short while ago did a a lot more modern day edition that I was digging big time. I’m signing up for
Krylon to share just one of their lovely Shade of the Yr spray paint palettes
for the new year! 
I Loved this “New Heritage” palette Krylon place with each other due to the fact it matches in so properly in our
dwelling. I use a large amount of deep accent shades so it was perfect. They have a couple of
distinctive shade mixtures for the new yr, but the just one I chose is a
attractive moody palette with their Fusion All-in-One Matte Black, Fusion
All-in-One Satin Peacock Blue, Fusion All-in-A single Matte Blue and their Chalky
Finish paint in classic white:
furniture leg candle DIY

You can locate the pine table legs at most components stores — they appear in
different types and heights. 

Just before you begin the undertaking, use a wrench to take away the screw from each
leg: 

prep table legs for candlesticks

This put up might contain affiliate hyperlinks for
your convenience. 

Then figure out the place you want to reduce each and every a single. I required to make positive the
heights various, so I marked wherever I preferred to reduce: 

furniture leg candlesticks

You can want to brace your sticks so you can drill into them for the taper
candle. Do NOT try out to keep them to do this! 

I found the metal clamp on my saw labored terrific, but you can also use clamps to
protected them to a desk:

brace on saw for drilling into candlesticks

I could not obtain my 7/8 inch paddle drill little bit, so I had to use a couple to get
the holes in there. I started with the 1/2 inch paddle drill bit — these are
so a lot less complicated to use in my viewpoint! They drill into the pine so effortlessly: 

drill bit for taper candle holders

And then I used a 7/8 inch uninteresting drill bit I experienced: 

drill bit size for taper candleholders

If you just start out with just the unexciting bit it will capture and isn’t going to reduce as
effortlessly. Employing the paddle little bit initially (or just a 7/8 paddle) is effective so a lot
better!

I gave all of the candlesticks a number of coats of the four colors (two in each and every
colour) and then caught the candles in!: 

furniture leg candlesticks in blue, black white

If your taper candles will not fit flawlessly, drip a little bit of wax in initially and they
will adhere! Sizzling glue also operates. 

All of these Krylon spray paints are both matte or satin end, so they
will give you a much more subdued end that I enjoy. 

I finished up purchasing a few extra smaller legs that did not need to have to be cut
down at all. They ended up already the great top and form. They are a enjoyable
accent and do the job so perfectly with our deep gray/blue paint colour (cyberspace by
Sherwin-Williams): 

Dark blue walls cane dresser

The shades get the job done so perfectly jointly and as constantly, the Krylon spray paint was
extremely uncomplicated to use. It goes on so quickly and addresses wonderful! As a reminder,
I made use of Fusion All-in-A single Matte Black, Fusion All-in-1 Satin Peacock Blue,
Fusion All-in-One particular Matte Blue and their Chalky End paint in basic white.

This was a quick Do-it-yourself and the opportunities are countless! You can use a less difficult
desk leg for a extra fashionable look, or use wooden bases from the craft shop for
the prime and base to make them a lot more standard. 

This post sponsored by Krylon but all views are my own. I only function with firms and goods I know, enjoy and would endorse to you. 

You can pin this project for later employing this impression!: 

table leg candlesticks DIY



Source website link